Model Specification Table
| Model | RSP-200-12 | RSP-200-24 | RSP-200-27.3 | RSP-200-36 | RSP-200-48 |
| Output Voltage | 12V | 24V | 27.3V | 36V | 48V |
| Rated Current | 16.7A | 8.5A | 7.3A | 5.5A | 4.2A |
| Current Range | 0–16.7A | 0–8.5A | 0–7.3A | 0–5.2A | 0–4.2A |
| Rated Power | 200W | 204W | 200W | 200W | 201.6W |
| Ripple Noise | 150mVp-p | 150mVp-p | 150mVp-p | 220mVp-p | 240mVp-p |
| Voltage Adj. Range | 10–13.2V | 20–26.4V | 23.5–29.5V | 32.4–39.6V | 41–56V |
| Voltage Tolerance | ±1.0% | ±1.0% | ±1.0% | ±1.0% | ±1.0% |
Input Parameters (Universal)
| Parameter | Description |
| Input Voltage Range | 88–264VAC or 124–370VDC |
| Input Frequency | 47–63Hz |
| PFC Efficiency | PF > 0.95 (230VAC) / PF > 0.98 (115VAC full load) |
| Input Efficiency | 88–90% (varies by model) |
| Input Current (Typical) | 4A/115VAC, 2A/230VAC |
| Surge Current | 20A/115VAC, 40A/230VAC |
| Leakage Current | <1.5mA/240VAC |
Protection Functions
| Protection Type | Trigger Condition | Response Action |
| Overload Protection | 115–135% of rated output power | Hiccup mode, auto-recovery after fault cleared |
| Overvoltage Protection | Output voltage exceeds threshold (model-dependent) | Output shutdown, auto-recovery after fault cleared |
| Overtemperature Protection | Excessive temperature | Output shutdown, auto-recovery when cooled down |
Environmental Requirements
| Parameter | Requirement |
| Operating Temperature | -30°C to +70°C (refer to derating curve) |
| Operating Humidity | 20–90% RH (non-condensing) |
| Storage Conditions | -40°C to +85°C, 10–95% RH |
| Temperature Coefficient | ±0.03%/°C (0–50°C) |
| Vibration | 10–500Hz, 2G (XYZ axes, 10 min/cycle × 60 cycles) |
Safety & Certification
| Item | Standard/Requirement |
| Safety Standards | GB 4943.1, EN 60950.1 APPROVED |
| Insulation Resistance | I/P-O/P: 100MΩ @ 500VDC/25°C/70%RH |
| Withstand Voltage | I/P-O/P: 3kVAC, I/P-FG: 2kVAC, O/P-FG: 0.5kVAC |
| EMC - Emission: EN55032 (CISPR32) Class B |
|
Additional Information
| Parameter | Description |
| MTBF (25°C) | ≥206.5K hours (MIL-HDBK-217F standard) |
| Dimensions | 215×115×30mm (L×W×H) |
| Packaging Weight | Single unit: 0.72kg; 30 units/box: 22.5kg, Volume: 0.78 cubic feet |
Notes
All unspecified parameters are measured at 230VAC input, full load, 25°C unless noted.
Ripple noise measurements use a bandwidth of 20MHz with 12-inch twisted-pair wires and parallel 0.1μF + 47μF capacitors.
Low-input voltage operation requires derating (refer to derating curves).
EMC testing uses a 1mm-thick steel plate (360×360mm).
Key Differences from RSP-320 Series
Power Rating: 200W vs. 320W.
Output Voltages: Includes 27.3V (common in telecom/dc systems).
Efficiency: Slightly lower (up to 90%) compared to the 320W series.
Cooling: Free air convection vs. forced air cooling in the 320W series.
Package Weight: Lighter (0.72kg vs. 0.9kg for 320W).
Model Specification Table
| Model | RSP-200-12 | RSP-200-24 | RSP-200-27.3 | RSP-200-36 | RSP-200-48 |
| Output Voltage | 12V | 24V | 27.3V | 36V | 48V |
| Rated Current | 16.7A | 8.5A | 7.3A | 5.5A | 4.2A |
| Current Range | 0–16.7A | 0–8.5A | 0–7.3A | 0–5.2A | 0–4.2A |
| Rated Power | 200W | 204W | 200W | 200W | 201.6W |
| Ripple Noise | 150mVp-p | 150mVp-p | 150mVp-p | 220mVp-p | 240mVp-p |
| Voltage Adj. Range | 10–13.2V | 20–26.4V | 23.5–29.5V | 32.4–39.6V | 41–56V |
| Voltage Tolerance | ±1.0% | ±1.0% | ±1.0% | ±1.0% | ±1.0% |
Input Parameters (Universal)
| Parameter | Description |
| Input Voltage Range | 88–264VAC or 124–370VDC |
| Input Frequency | 47–63Hz |
| PFC Efficiency | PF > 0.95 (230VAC) / PF > 0.98 (115VAC full load) |
| Input Efficiency | 88–90% (varies by model) |
| Input Current (Typical) | 4A/115VAC, 2A/230VAC |
| Surge Current | 20A/115VAC, 40A/230VAC |
| Leakage Current | <1.5mA/240VAC |
Protection Functions
| Protection Type | Trigger Condition | Response Action |
| Overload Protection | 115–135% of rated output power | Hiccup mode, auto-recovery after fault cleared |
| Overvoltage Protection | Output voltage exceeds threshold (model-dependent) | Output shutdown, auto-recovery after fault cleared |
| Overtemperature Protection | Excessive temperature | Output shutdown, auto-recovery when cooled down |
Environmental Requirements
| Parameter | Requirement |
| Operating Temperature | -30°C to +70°C (refer to derating curve) |
| Operating Humidity | 20–90% RH (non-condensing) |
| Storage Conditions | -40°C to +85°C, 10–95% RH |
| Temperature Coefficient | ±0.03%/°C (0–50°C) |
| Vibration | 10–500Hz, 2G (XYZ axes, 10 min/cycle × 60 cycles) |
Safety & Certification
| Item | Standard/Requirement |
| Safety Standards | GB 4943.1, EN 60950.1 APPROVED |
| Insulation Resistance | I/P-O/P: 100MΩ @ 500VDC/25°C/70%RH |
| Withstand Voltage | I/P-O/P: 3kVAC, I/P-FG: 2kVAC, O/P-FG: 0.5kVAC |
| EMC - Emission: EN55032 (CISPR32) Class B |
|
Additional Information
| Parameter | Description |
| MTBF (25°C) | ≥206.5K hours (MIL-HDBK-217F standard) |
| Dimensions | 215×115×30mm (L×W×H) |
| Packaging Weight | Single unit: 0.72kg; 30 units/box: 22.5kg, Volume: 0.78 cubic feet |
Notes
All unspecified parameters are measured at 230VAC input, full load, 25°C unless noted.
Ripple noise measurements use a bandwidth of 20MHz with 12-inch twisted-pair wires and parallel 0.1μF + 47μF capacitors.
Low-input voltage operation requires derating (refer to derating curves).
EMC testing uses a 1mm-thick steel plate (360×360mm).
Key Differences from RSP-320 Series
Power Rating: 200W vs. 320W.
Output Voltages: Includes 27.3V (common in telecom/dc systems).
Efficiency: Slightly lower (up to 90%) compared to the 320W series.
Cooling: Free air convection vs. forced air cooling in the 320W series.
Package Weight: Lighter (0.72kg vs. 0.9kg for 320W).
{"json":"[{\"photoId\":\"401000854\",\"photoType\":\"pdf\",\"photoSize\":\"554\",\"name\":\"RSP-200 SPEC.pdf\",\"fileId\":\"12012664\",\"encodeFileId\":\"fyKUghALClQt\",\"photoUrlNormal\":\"//rjrorwxhikmrlm5p-static.micyjz.com/static/assets/widget/images/downloadNew/pdf.svg\"}]","type":"1"}
