DR-60 60W Din Rail Power Supply

Description:

The DR-60 is a commonly used rail-mounted switch mode power supply, extensively applied in fields such as industrial automation, electrical control cabinets, LED lighting, and security surveillance. Below is a general introduction and overview of its features:

Features:

• Universal AC input/Full range

• Protections:Short circuit/Overload/Over voltage

• Cooling by free air convection

• Can be installed on DIN RAIL TS-35/7.5 or 15

• LED indicator for power on

• No load power consumption<0.75W

• 100% full load burn-in test

• 2 years warranty
  

Applications:

• Industrial Automation: Powers PLCs, sensors, actuators, and other control components.

• LED Lighting: Supplies stable power to small to medium-sized LED lighting fixtures.

• Security Surveillance: Powers CCTV cameras, access control systems, and other security equipment.

• Communication Equipment: Suitable for small-scale switches, routers, and the like.

• Instrumentation: Provides power support for various measuring and testing equipment.

Specifications:

Model		DR-60-12	DR-60-24	DR-60-48
Output	DC Voltage	12V	24V	48V
	Current Range	0-5A	0-2.5A	0-1.25A
	Rated Power	60W	60W	60W
	Ripple Noise(Max)	80mVp-p	100mVp-p	120mVp-p
	Voltage Adj.Range	12-15V	24-30V	48-55V
	Voltage Tolerance	±1.5%	±1.0%	±1.0%
	Line Regulation	±0.5%	±0.5%	±0.5%
	Load Regulation	±1.5%	±1.0%	±1.0%
	Set up,Rise time	500ms,30ms/230VAC   1000ms,30ms/115VAC(full load)
	Hold up Time	60ms/230VAC     12ms/115VAC(full load)
Input	Voltage Range	85 ~264VAC    120~370VDC
	Frequency	47 ~ 63Hz
	Efficiency	77%	81%	83%
	AC Current	0.55A/115VAC    4A/230VAC
	Inrush Curent	40A/230VAC
	Leakage Current	<1mA / 240VAC
Protection	Overload	105 ~ 130% rated output power
		Protection tye:Constant current limiting,recovers automatically after fault condition is removed
	Over Voltage	14-17V	29-33V	56-65V
		Protection type : Shut off o/p voltage, re-power on to recover
Environment	Working Temperature	-10~ +60℃ (Refer to derating curve as datasheet from SMUN)
	Working Humidity	20 ~ 90% RH non-condensing
	Storage Temp.Humidity	-20 ~ +85℃, 10 ~ 95% RH
	Temp.Coefficient	±0.03%/℃ (0 ~ 50℃)
	Vibration	Component：10~500Hz,2G 10min./1 cycle，60min. each along X,Y,Z axes
Safety	Safety Standards	CE and GB4943.1 Safety standard
	Withstand Voltage	I/P-O/P:1.5KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC
	Isolation Resistance	I/P-O/P, I/P-FG, O/P-FG:>100M Ohms / 500VDC/25℃/70% RH
	EMC Emission	Compliance to EN61000-3-2:2014/EN61000-3-3:2013
	EMC Immunity	Compliance to EN55032:2015/EN55035:2017/60950-1
Others	MTBF	≥327.9K hrs MIL-HDBK-217F(25℃)
	Dimension	93*78*56mm (L*W*H)
	Packing	0.25Kg; 60pcs/15Kg
Note	1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25℃ of ambient temperature.  2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.  3. Tolerance : includes set up tolerance, line ragulation and load regulation.  4. The power supply is considered a component which will be installed into final equipment. The final equipment must be re-confirmed that it still meets EMC directives.  5. Installation clearances : 40mm on top, 20mm on the bottom, 5mm on the left and right side are recommended when loaded permanently with full power.In case the adjacent device is a heat soure, 15mm clearance is recommended 6. Derating may be needed under low input voltage. Please check the derating curve for more details. 7.Please contact with SMUN customer service for more details.

{"json":"[{\"photoId\":\"347147904\",\"photoType\":\"pdf\",\"photoSize\":\"832\",\"name\":\"DR-60 SPEC.pdf\",\"fileId\":\"6472104\",\"encodeFileId\":\"ekKfpbZcrLAE\",\"photoUrlNormal\":\"//rjrorwxhikmrlm5p-static.micyjz.com/static/assets/widget/images/downloadNew/pdf.svg\"}]","type":"1"}